The self-aligning ball bearing has cylindrical hole and conical hole. The cage is made of steel plate and synthetic resin. Its feature is that the outer ring raceway is spherical, with automatic self-aligning, which can compensate the errors caused by different centrality and shaft deflection, but the relative inclination of the inner and outer rings shall not exceed 3 degrees.
Self aligning ball bearing is a kind of bearing with spherical ball between the inner ring of two raceways and the outer ring with spherical raceway.
The curvature center of the outer ring raceway surface is consistent with the bearing center, so it has the same self-aligning function as the automatic self-aligning ball bearing. When the shaft and shell are flexed, it can be adjusted automatically without increasing the bearing load. Self aligning roller bearing can bear radial load and axial load in two directions. Radial load capacity, suitable for heavy load, shock load. The inner diameter of the inner ring is a taper hole bearing, which can be directly installed. Or it can be installed on the cylindrical shaft by using the fastening sleeve and the dismounting cylinder. The cages are made of steel stamping cages, polyamide forming cages and copper alloy car cages.
The self-aligning ball bearing has cylindrical hole and conical hole. The cage is made of steel plate and synthetic resin. Its feature is that the outer ring raceway is spherical, with automatic self-aligning, which can compensate the error of self-aligning ball bearing caused by different centrality and shaft deflection, but the relative inclination of the inner and outer rings shall not exceed 3 degrees.
It can bear large radial load and certain axial load. The outer ring raceway of this kind of bearing is spherical, so it has self-aligning performance. When the shaft is bent or tilted by force, the relative inclination between the inner ring center line and the outer ring center line does not exceed 1 °~ two point five ° The bearing can still work at the same time.
There are two kinds of bore in self-aligning ball bearings: cylindrical bore and conical bore. The taper of conical inner hole is 1:12 or 1:30. In order to enhance the lubrication performance of the bearing, an annular oil groove and three oil holes are machined on the outer ring of the bearing.
It can bear radial load and small axial load. The axial displacement of the shaft (shell) is limited within the clearance limit, and it has the function of automatic centering. It can work normally under the condition that the inner and outer parts are not inclined relatively. It is suitable for parts where the coaxiality of the supporting seat hole cannot be strictly guaranteed.
The self-aligning ball bearing with dust cover and sealing ring has been filled with proper amount of grease during assembly. It should not be heated or cleaned before installation. It does not need to be lubricated during use. It can adapt to the operating temperature between - 30 ℃ and + 120 ℃. Self aligning ball bearings are widely used in precision instruments, low noise motors, automobiles, motorcycles and general machinery
Mini Series: 10x, 12x, 13X
General series: 12xx, 13xx, 22xx, 23xx
Self aligning ball bearing is suitable for bearing heavy load and impact load, precision instrument, low noise motor, automobile, motorcycle, metallurgy, rolling mill, mining, oil, paper, cement, sugar and other industries and general machinery
Rolling bearing classification Abstract:
1. Classification by rolling bearing structure type
(1) According to the load direction or the nominal contact angle that the bearing can bear, it can be divided into:
1) Radial bearing --- mainly used to bear radial load of rolling bearing, its nominal contact angle from 0 to 45.
According to the different nominal contact angle, it can be divided into three parts
Radial contact bearing -- radial bearing with nominal contact angle of 0
Radial angular contact bearing -- radial bearing with nominal contact angle greater than 0 to 45.
2) Thrust bearing --- mainly used to bear axial load of rolling bearing, its nominal contact angle is greater than 45 to 90.
According to the nominal contact angle, it can be divided into three parts
Axial contact bearing --- thrust bearing with nominal contact angle of 90:
Thrust angular contact bearing -- thrust bearing with nominal contact angle greater than 45 but less than 90.
(2) According to the types of rolling elements, bearings are divided into:
1) Ball bearing --- the rolling element is ball
2) Roller bearing --- the rolling element is roller. According to the types of rollers, roller bearings are further divided into:
Cylindrical roller bearing --- rolling element is the bearing of cylindrical roller, the ratio of length and diameter of cylindrical roller is less than or equal to 3;
Needle roller bearing ---- the rolling element is the bearing of needle roller. The ratio of needle length to diameter is greater than 3, but the diameter is less than or equal to 5mm;
Tapered roller bearing --- rolling element is tapered roller bearing;
Self aligning roller bearing - rolling element is spherical roller bearing.
(3) According to whether the bearing can be self-aligning during operation, it is divided into three parts
1) Self aligning bearing --- the raceway is spherical and can adapt to the angular deviation and angular motion between the axis lines of two raceways;
2) Non self aligning bearing (rigid bearing) - bearing that can resist the angular deviation of axis line between raceways.
(4) According to the number of rolling element columns, bearings are divided into:
1) Single row bearing -- bearing with a row of rolling elements;
2) Double row bearing -- bearing with two rows of rolling elements;
3) Multi row bearings --- bearings with more than two rows of rolling elements, such as three row and four row bearings.
(5) According to whether the parts of bearings can be separated, they are divided into three parts
1) Separable bearing -- bearing with separable parts;
2) Non separable bearing -- bearing in the final matching, rings are not free to separate the bearing.
(6) According to its structural shape (such as whether there is a filling groove, whether there is an inner ring, an outer ring, the shape of the ring, the structure of the rib, and even whether there is a cage, etc.), the bearing can also be divided into a variety of structural types.
2. According to the size of rolling bearing, the bearing is divided into three parts according to its outer diameter
(1) Miniature bearing ---- bearing with nominal outer diameter less than 26mm;
(2) Small bearings --- bearings with nominal outer diameter of 28-55mm;
(3) Small and medium sized bearings --- bearings with nominal outer diameter of 60-115mm;
(4) Medium and large bearings --- bearings with nominal outer diameter of 120-190mm;
(5) Large bearing --- bearing with nominal outer diameter of 200-430mm;
(6) Super large bearing --- bearing with nominal outer diameter over 440mm.
National standard: GB / t272-93 (to ISO) (instead of gb272-88), the composition of rolling bearing code is shown in the attached table. Code representation method of rolling bearing code purpose: to characterize the structure, size, type, accuracy, etc. of rolling bearing. The code is specified by the national standard GB / T272-93.